Description

to purchase Auto Keys, Fobs, Remotes, Shell/Cases & Related products for 2014 Buick Regal

Step-by-Step Programming Instructions:

Programming with a Recognized Transmitter (Key Vehicles Only):
1. Insert the original, already programmed key into the ignition and turn it to the ON/RUN position.
2. Turn the key to LOCK/OFF, and remove it.
3. Insert the new key to be programmed and turn it to the ON/RUN position within five seconds. The security light will turn off once the key has been programmed.
4. Repeat Steps 1–3 if additional keys need to be programmed.

Programming without a Recognized Transmitter (Key Vehicles Only):
If a recognized key is not available, contact your dealer. Follow this procedure to program the first key. This process will take approximately 30 minutes to complete for the first key. Ensure the vehicle is off, and all keys you wish to program are with you.
1. Insert the new vehicle key into the ignition.
2. Turn to ON/RUN. The security light will come on.
3. Wait for 10 minutes until the security light turns off.
4. Turn the ignition to LOCK/OFF.
5. Repeat Steps 2–4 two more times. After the third time, turn to ON/RUN; the key is learned, and all previously known keys will no longer work with the vehicle. Remaining keys can be learned by following the procedure in “Programming with a Recognized Transmitter (Key Vehicles Only).”

Programming with a Recognized Transmitter (Keyless Access Vehicles Only):
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. Ensure the vehicle is off, and all transmitters, both recognized and new, are with you.
1. Place the recognized transmitter(s) in the cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.
2. Insert the vehicle key of the new transmitter into the key lock cylinder located on the outside of the driver door and turn the key counterclockwise to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4, or 5.
3. Place the new transmitter into the transmitter pocket with the buttons facing up. The transmitter pocket is located inside the center console cupholder.
4. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.
5. Remove the transmitter from the transmitter pocket and press unlock. To program additional transmitters, repeat Steps 3–5. When all additional transmitters are programmed, press and hold the ignition for 12 seconds to exit programming mode. Reinstall the rubber cup liner.

Programming without a Recognized Transmitter (Keyless Access Vehicles Only):
If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This process will take approximately 30 minutes to complete. Ensure the vehicle is off, and all transmitters you wish to program are with you.
1. Insert the vehicle key of the transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position, counterclockwise, five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press the ENGINE START/STOP button. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time, all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE #1.
4. Place the new transmitter into the transmitter pocket with the buttons facing up. The transmitter pocket is located inside the center console cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.
5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.
6. Remove the transmitter from the transmitter pocket and press unlock. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for 12 seconds to exit programming mode.

to purchase Auto Keys, Fobs, Remotes, Shell/Cases & Related products for 2014 Buick Regal