How to Program a 2019 Mitsubishi Mirage Ignition Smart Chip Key Transponder

Step by Step How to Programming Instructions:

To add a new key to your Remote Head Key System, ensure you have two already programmed keys. You can program up to 8 keys in total.

1. Insert the first valid key into the ignition switch and turn it to the “ON” position for 5 seconds.
2. Turn the key to the “OFF” position and remove it.
3. Within 30 seconds of removing the first key, insert the second valid key into the ignition and turn it to the “ON” position. Approximately 10 seconds later, the immobilizer display will start blinking.
4. When the immobilizer display starts blinking, turn the second valid key to the “OFF” position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition switch and turn it to the “ON” position. Ensure this operation is completed within 30 seconds after the immobilizer display starts blinking. When programming is complete, the immobilizer display will come on for 30 seconds then go off. If an error occurs, the blinking immobilizer display will go off during the procedure.
5. If you wish to register another key, repeat the process from step 1.

To program the remote portion of your key, follow these instructions:

You can program the remote portion to the system if you have one valid (already programmed) key by doing the following:

1. Have available all (current and new) keys you wish to register.
2. With a valid (already registered) key, press the UNLOCK button (2) for 4 to 10 seconds. Then press and hold the LOCK button.
3. Within 10 seconds of pressing the LOCK button, release the LOCK and UNLOCK buttons in sequence. At this time, programming for all keys that are programmed except for the key used in steps 2 and 3 are erased, and the answer back function (door is locked and unlocked) informs you that the registration mode has been activated.
4. Within 60 seconds after step 3, complete the following ID code registration operation using the next key you wish to register within 4 seconds:
– Press both the LOCK and UNLOCK buttons for 2 seconds.
– Release both the LOCK and UNLOCK buttons for 1 second.
– Press the UNLOCK button. The answer back function informs you that the ID code registration of the key is completed.
5. To register the ID codes of additional keys, repeat step 4 within 60 seconds after step 4.
6. If no ID code of a key is registered within 60 seconds after step 4, the registration mode is canceled, and the normal mode returns.

For programming with the Fast Key Smart Key System:

Ensure you have two valid (already programmed) Fast keys and a blank (not programmed) Fast key. Follow the procedures below:

1. Open the driver’s door and keep it open until Fast key programming is finished. Do not open or close other doors.
2. While carrying the first valid Fast key, put the operation mode in ON within 30 seconds.
3. With the first valid Fast key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.
4. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step 3.
5. With the second valid Fast key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.
6. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step 5.
7. Touch the bottom back portion of the new Fast key to the engine switch. When registration of ID code is complete, the buzzer will sound three times, and the immobilizer display will come on for 30 seconds. If an error occurs, Fast key programming will be terminated, and the buzzer will sound for 3 seconds.

Note:
– Fast key programming will be terminated if the operation mode is put in OFF before the immobilizer display starts blinking.
– If you wish to register another Fast key, repeat the process from step 1 after the operation mode is put in OFF.
– The immobilizer display will go off immediately if the operation mode is put in OFF.
– Perform the operation when the interrupt display screen is not showing. The interrupt display screen may prevent you from seeing the immobilizer display.
– It is not possible to register a Fast key if the immobilizer display goes off during the procedure.