How to Program a 2020 Chevrolet Silverado Ignition Smart Chip Key Transponder
Step by Step How to Programming Instructions:
**Programming with a Recognized Key (Key Vehicles Only):**
1. Insert the original, already programmed key into the ignition and turn it to the ON/RUN position.
2. Turn the key to LOCK/OFF and remove it.
3. Insert the new key to be programmed and turn it to the ON/RUN position within five seconds. The security light will turn off once the key has been programmed.
4. Repeat Steps 1–3 if additional keys are to be programmed.
**Programming without a Recognized Key (Key Vehicles Only):**
Program a new key to the vehicle when a recognized key is not available. Canadian regulations require owners to see their dealer. If there are no currently recognized keys available, follow this procedure to program the first key. This procedure will take approximately 30 minutes to complete for the first key. The vehicle must be off, and all the keys you wish to program must be with you.
1. Insert the new vehicle key into the ignition.
2. Turn to ON/RUN. The security light will come on.
3. Wait for 10 minutes until the security light turns off.
4. Turn the ignition to LOCK/OFF.
5. Repeat Steps 2–4 two more times. After the third time, turn to ON/RUN; the key is learned, and all previously known keys will no longer work with the vehicle. Remaining keys can be learned by following the procedure in “Programming with a Recognized Key.”
**Smart Key System Programming with a Recognized Transmitter (Keyless Access Vehicles Only):**
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off, and all transmitters, both currently recognized and new, must be with you.
1. Remove the key from the recognized transmitter.
2. Place the recognized transmitter(s) in the cup holder or passenger seat.
3. Insert the vehicle key into the key lock cylinder on the driver door handle. Then turn the key counterclockwise to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays “READY FOR REMOTE #2, 3, 4, ETC.”
4. Place the new transmitter in the transmitter pocket/insert. Open the center console storage area and the storage tray. The transmitter pocket/insert is in front of the storage area next to the center console storage area between the driver and front passenger seats.
5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
6. Remove the transmitter from the transmitter pocket and press unlock or lock on the transmitter. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
7. Return the key back into the transmitter.
**Programming without a Recognized Transmitter (Keyless Access Vehicles Only):**
If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off, and all transmitters to be programmed must be with you.
1. Remove the vehicle key from the transmitter.
2. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays “REMOTE LEARN PENDING, PLEASE WAIT.”
3. Wait for 10 minutes until the DIC displays “PRESS ENGINE START BUTTON TO LEARN,” then press the ENGINE START/STOP button. The DIC display will again show “REMOTE LEARN PENDING, PLEASE WAIT.”
4. Repeat Step 3 two additional times. After the third time, all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show “READY FOR REMOTE #1.”
5. Place the new transmitter in the transmitter pocket/insert. Open the center console storage area and the storage tray. The transmitter pocket/insert is in front of the storage area next to the center console storage area between the driver and front passenger seats.
6. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
7. Remove the transmitter from the transmitter pocket/insert and press unlock or lock on the transmitter. To program additional transmitters, repeat Steps 5–7. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
8. Return the key back into the transmitter.
