404 Not Found


nginx
404 Not Found

404 Not Found


nginx
How to Program a 2015 Chevrolet Impala Ignition Smart Chip Key Transponder - KeyLessCanada : Instructions

Powered By
KeylessCanada.com

PROGRAMMING INSTRUCTIONS:

How to Program a 2015 Chevrolet Impala Ignition Smart Chip Key Transponder

0
27

Compare
SKU: Chevrolet Impala 2015 Categories: , , , Tags: , ,

Description

Click Hereto purchase Auto Keys, Fobs, Remotes, Shell/Cases & Related products for 2015 Chevrolet Impala

Step-by-Step Programming Instructions:

Programming Keys and Transmitters

Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to eight transmitters matched to it.

Programming with a Recognized Transmitter (Key Vehicles Only)

To program a new key:
1. Insert the original, already programmed key into the ignition and turn it to the ON/RUN position.
2. Turn the key to the LOCK/OFF position and remove it.
3. Insert the new key to be programmed and turn it to the ON/RUN position within five seconds. The security light will turn off once the key has been programmed.
4. Repeat Steps 1–3 if additional keys are to be programmed. If a key is lost or damaged, visit your dealer to have a new key made.

Programming without a Recognized Transmitter (Key Vehicles Only)

To program a new key when a recognized key is not available:
1. Insert the new vehicle key into the ignition and turn it to ON/RUN. The security light will come on.
2. Wait for 10 minutes until the security light turns off.
3. Turn the ignition to LOCK/OFF.
4. Repeat Steps 1–3 two more times. After the third time, turn to ON/RUN; the key is learned, and all previously known keys will no longer work with the vehicle. Remaining keys can be learned by following the procedure in “Programming with a Recognized Key.”

Programming with a Recognized Transmitter (Keyless Access Vehicles Only)

To program a new transmitter when there is one recognized transmitter:
1. Place the recognized transmitter(s) in the cup holder.
2. Remove the key lock cylinder cap. Then insert the vehicle key into the key lock cylinder on the driver door handle and turn the key counterclockwise to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4, or 5.
3. Place the new transmitter into the transmitter pocket inside the center console storage area.
4. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC will indicate readiness to program the next transmitter.
5. Remove the transmitter from the transmitter pocket and press UNLOCK. To program additional transmitters, repeat Steps 3–5. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for 12 seconds to exit programming mode.

Programming without a Recognized Transmitter (Keyless Access Vehicles Only)

To program up to eight transmitters when there are no recognized transmitters available:
1. Remove the key lock cylinder cap. Then insert the vehicle key into the key lock cylinder on the driver door handle and turn the key counterclockwise to the unlock position five times within 10 seconds. The DIC displays REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. The DIC will again show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time, all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.
4. Place the new transmitter into the transmitter pocket inside the center console storage area.
5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC will indicate readiness to program the next transmitter.
6. Remove the transmitter from the transmitter pocket and press UNLOCK. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for 12 seconds to exit programming mode.

Click Hereto purchase Auto Keys, Fobs, Remotes, Shell/Cases & Related products for 2015 Chevrolet Impala

Leave a reply

X
X